Best Portable Fish Finder

Best Portable Fish Finder

Advantages of Portable Fish Finders
More affordable. In general, fixed finders are usually more costly compared to portable units.
Flexibility. Portable fish finders can be easily transported and so can be used in different locations. If you are fishing from a land based location, a kayak or from a boat you are renting, the portable type of fish finder is the perfect choice for you.
Ease of use. Since there’s no permanent installation required, it’s easy to set up the device and have it in use in moments.
Transducer flexibility. If you liked this write-up and you would certainly such as to get additional details concerning best portable fishfinder kindly see our site. The transducer can also be conveniently used in different situations. You can easily throw it into the water from the dock, boat or shoreline. Optionally, you can also temporarily mount it onto your kayak, canoe or other watercraft.
Mounting Transducer on a Kayak
There are several ways for mounting a transducer on a kayak. You can either install it in the hull, mount it on the back, or near the rudder. Other options include using a portable kit and attaching it to the kayak with a suction cup or just letting dangle over the side of the kayak. The last option might not be ideal as it reduces the life of the equipment. So first decide where to mount the transducer.

Installing to the hull is one of the most common ways. For this method, you should start by choosing a good, flat spot on the hull where you will install the transducer. Lightly sand to rough up the area and clean away any dust, debris or grime.

Apply marine goop to the bottom of the transducer, but make sure that there are no trapped air bubbles, as they will compromise the readings. Place the transducer to that spot. Press it down and move a little from side to side till it’s all the way down against the hull. Tape down with duct tape on top. You can remove the tape once the goop dries out a bit and then wait for 24-48 hours for the loop to try out completely. The transducer should not be moved during drying.

Another method to use is through the scupper hole. Though it has one drawback – one of your scupper holes will be plugged up. This is a good option if you are buying a Lowrance portable fish finder, as the brand offers a special scupper kayak transducer mount that is easy to install. You just fit the transducer on the mount and stick it through the scupper hole.

One more easy way to mount it is on the back of the kayak, near the rudder. For this installation, you will need to mount a metal or plastic plate to a flat area on the back of the kayak. Then you mount the transducer onto that plate and run the wire to the place you where you will mount the fish finder. Just make sure that the transducer is above the rudder and the bottom of the kayak.

Optionally, you can acquire a portable kit, which usually includes a battery, suction cup, and bungee cords. The suction cup allows mounting the transducer wherever you want on your kayak. It’s very easy to mount, and just as easy to remove.

Things to Consider When Using a Fish Finder on a Kayak
First, you should start by positioning your fish finder on the kayak. Several of the options of the transducer mount I have mentioned above. The perfect position would depend on several factors, one of them the type of kayak you have. Then make sure that you install it within reach, so at any time you can easily reach out and change the settings on the unit. Also, the fish finder should not interfere with your working space, so it shouldn’t be in the way of your bait, rigging gear, or your paddle stroke.
One of the important features that a kayak fish finder should have is waterproofness. Check that the device carries a waterproof rating of at least IP67. IP means "Ingress Protection" and the numbers show the level of protection against solids and liquids. However, even though the unit is waterproof, it does not mean that you can blast it with water with a high-pressure house when cleaning your kayak. So put the electronics safely away.
Since on a kayak you don’t have the ability to plug your electronics into a power socket, you will need to carry a battery for a power source. To choose the right size of the battery, check the milliamps of your fish finder.
You will need to find a storage place for the battery, where it will be protected from the salt water, which corrode and shorten its life. To secure the battery you can design a foam block or a battery tray and then glue it into the hull of your kayak.
To get the power to your fish finder you will need to run a wire between the two. Solder all the connections (just crimping does not exclude moisture that can eventually wick into the wire) and make sure that you seal well with no exposed joints left. To further keep the moisture out give it a quick coat of protectant. It’s also recommended to apply the protectant to the plugs and sockets.
When using a fish finder on a kayak it’s also important to take proper after care. During the day it will get exposed to saltwater, so once you get home at once remove that crusty layer of salt. Just give it a quick wash with some tepid fresh water. Once dry, store it away in a dry box.
Other necessary fishing equipment like proper boots, outwear.